Schweizer300CB 直昇機飛行前檢查程序

                初步檢查                                   發動機右側                                  尾樑左側

          1.直昇機水平..................檢查                   1.皮帶輪.......................檢查                        1.柳釘及蒙皮.....................檢查

          2.停機位情況..................檢查                   2.尾槳控制連線...........檢查                        2.尾樑支撐.........................檢查

          3.旋翼光潔......................檢查                   3.滑油冷却器...............檢查                        3.支架尾部.........................檢查

                   4.滑油管............無漏/過熱/腐蝕                 4.排氣尾管支撐.................檢查     

          5.油箱..................測量/記錄/蓋緊             5.加熱軟管...................檢查                                   發動機左側

                    機艙                                              6.排氣系統.排氣管......檢查無損                1.油箱.................................檢查

          1.全部開關儀器..............關                             7.發動機.基本狀況.......各部件                   2.離合器皮帶....................檢查

          2.配平/性能..............在包線內 /計算           主傳動.軌桿.旋翼頭                           3.遮蓋物.............................檢查

          3.機載文件......................在機上               1.主傳動.軌桿...............檢查                       4.發電機皮帶....................檢查

          4.電瓶開關......................開                       2.傳動滑油量................檢查                       5.發動機滑油量................檢查

          5.油量表..........................檢查顯示           3.控制桿........................檢查                       6.滑油過濾器蓋................檢查

          6.離合器電門..................打開,燈滅          4.混合曲軸....................檢查                       7.滑油泵............................檢查

          7.信號/位置/著陸燈........開/檢查/關         5.軸承............................檢查                       8.排氣系統,排氣管...........檢查無損

          8.離合器位置標記..........檢查                   6.俯仰連接................擺動自由                   9.燃油沉淀器....................查油樣

          9.離合器皮帶..................調整張力           7.主旋翼頭....................潤滑                     10.發動機,基本狀況...........各部件

        10.離合器彈簧和連線......檢查                   8.主旋翼阻尼................無漏                                   機身左側

        11.離合器作動器..............調整/緊密          9.主旋翼刀鋒................光潔                       1.艙門,插銷.......................檢查    

        12.離合器開關..................鬆開                        發動機後部                                   2.左上艙蓋窗....................檢查

        13.腳踏..............................調整,緊密          1.上部離合....................檢查                       3.腳蹬金屬片..................損害/污染

        14.急救箱 /滅火筒............檢查                   2.離合皮帶....................檢查                       4.備用進氣口....................檢查

        15.安全帶..........................檢查                   3.皮帶輪/下部配對齒輪......前後移動        5.前部支柱........................檢查

        16.可卸控制桿..................檢查                   4.下部帶輪軸承............檢查                       6.前減震............................檢查

        17.羅盤校正卡..................裝備正確           5.中間結構....................檢查                       7.阻力支架......................檢查對準

        18.電瓶開關......................關                       6.尾槳驅動齒輪............檢查                       8.後支架............................檢查

                   機身右側                                    尾樑右側                                               9.後減震............................檢查

          1.艙門 /插銷....................檢查                   1.柳釘及蒙皮................檢查                      10.右防滑管/靴..................檢查

          2.右上艙蓋窗..................檢查                   2.驅動齒輪阻尼............檢查                                    機頭

          3.腳蹬金屬片..................損害/污染          3.尾槳鋼索....................檢查                       1.艙蓋...............................光潔

          4.電瓶..............................檢查                   4.尾樑支撐....................檢查                       2.溫度計遮光板...............檢查

          5.電線 /電氣設備............檢查                   5.支架尾部....................檢查                       3.空速管...........................檢查

          6.前橫樑..........................無彎曲               6.静壓管.....................無遮蔽                      4.無線電天線...................檢查

          7.前部支柱......................檢查                         尾槳                                            5.進氣系統.......................檢查

          8.前減震..........................檢查                   1.水平平衡器................檢查                       6.應答機天線...................檢查

          9.阻力支架......................檢查對準           2.尾槳齒輪....................檢查

        10.後橫樑..........................檢查                   3.尾槳齒輪箱................檢查

        11.後支架..........................檢查                   4.尾槳控制桿................檢查

        12.後減震..........................檢查                   5.軸承............................檢查

        13.右防滑管 /靴................檢查                   6.俯仰連接....................檢查

                                                                              7.鉸鏈軸承....................檢查

                                                                              8.螺栓............................檢查

                                                                              9.槳葉............................光潔